 "Steering Shaft Support 19mm Type II" (SKU: FK1019)"Type ll has two mounting holes...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
"Steering Shaft Support, 20mm, Type II" (SKU: FK2019)"Type ll has two mounting holes...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 "Steering Shaft Support, 19mm, Type I" (SKU: FK1018)"Type l has one mounting hole...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
"Steering Shaft Support, 20mm, Type I" (SKU: FK2018)"Type l has one mounting hole...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 "Steering Shaft Support, 5/8"" , Type III" (SKU: FK1011)"Type lll has three mounting holes, one above & two below the shaft brg...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
"Steering Shaft Support, 5/8"", Type II" (SKU: FK828)"Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 "Steering Shaft Support, 5/8"", Type IV" (SKU: FK1012)"Type lV has three mounting holes below the shaft brg...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
"Steering Shaft Support, 5/8"", Type I" (SKU: FK827)"Type l has one mounting hole...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 Control Rods (Tie rods). 3/8 NF x 10 3/4 Inches (SKU: FK8108)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 10 Inches (SKU: FK8100 )Fast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 11 1/2 Inches (SKU: FK8115)Fast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 11 Inches (SKU: FK8110)Fast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
|
Control Rods (Tie rods). 3/8 NF x 12 1/2 Inches (SKU: FK8125)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 12 3/8 Inches (SKU: FK8124)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 13 1/4 Inches (SKU: FK8133 )Fast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 13 5/8 Inches (SKU: FK8136 )Fast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
 Control Rods (Tie rods). 3/8 NF x 6 1/2 Inches (SKU: FK8650)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 7 3/4 Inches (SKU: FK8775)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 7 Inches (SKU: FK8700)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 8 1/2 Inches (SKU: FK8850)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
|
Control Rods (Tie rods). 3/8 NF x 8 1/4 Inches (SKU: FK8825)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 8 Inches (SKU: FK8800)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 9 1/2 Inches (SKU: FK8950)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 9 1/4 Inches (SKU: FK8925)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
|
Control Rods (Tie rods). 3/8 NF x 9 3/4 Inches (SKU: FK8975)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 9 5/8 Inches (SKU: FK8963)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 3/8 NF x 9 Inches (SKU: FK8900)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 10 1/2 Inches (SKU: FK9105)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
|
Control Rods (Tie rods). 5/16 NF x 10 Inches (SKU: FK9100)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 11 1/2 Inches (SKU: FK9115)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 11 Inches (SKU: FK9110)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 12 Inches (SKU: FK9120)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
|
Control Rods (Tie rods). 5/16 NF x 13 Inches (SKU: FK9130)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 14 1/2 Inches (SKU: FK9145)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 7 Inches (SKU: FK9700)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 8 1/2 Inches (SKU: FK9850)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
|
Control Rods (Tie rods). 5/16 NF x 9 1/2 Inches (SKU: FK9950)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 9 Inches (SKU: FK9900)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
 Publication - "Dynamics of Speed" (SKU: DOS 0001)"Dynamics of Speed" is a reference book specifically for karting, a worthy addition to your library.
|
 Rod Ends, 3/8" Male Threrad ~ LH and RH (SKU: CH008)For your steering system or any other use. These fit our 3/8" threaded Control Rods (Tie Rods).
Please note LH or RH on the order form and the quantity you need of each.
|
|
Rod Ends, 5/16" Male Thread ~ LH and RH (SKU: CH007)These are for karts using the smaller 5/16" rod ends. Note on the order form LH or RH thread and the quantity of each needed.
Generally each tie rod uses 1 of each. These fit our 5/16" Control Rods (Tie Rods).
|
 Steering Lock for 5/8" Shaft (SKU: FK850)"This is the Lock & Pin only for a 5/8"" steering shaft. See FK835 for lock w/steering block."
|
 Steering lock & Steering block Set 20mm shaft ~ (New) (SKU: FK8020)Steering lock with matching steering shaft block (FK2019) to aid in setting steering geometry. Use with 20mm shaft.
|
Steering lock only 19mm shaft (SKU: FK819)Steering lock . Use with 19mm shaft...
|
|
Steering Lock only: 20mm shaft (New) (SKU: FK820)Locks the steering for wheel alignment & toe-in adjustments.
|
Steering Support w/Lock, 19mm (SKU: FK8019)"Included is a Type II Steering Block, Steering lock & Pin for a 19mm steering shaft."
|
Steering Support w/Lock, 5/8" Shaft (SKU: FK835)Included is a Type II Steering Block, Steering lock & Pin for a 5/8"" steering shaft.
|
 Wheel Alignment Discs For Van-K Wheels (SKU: FK2070)Steel Wheel Alignment Discs allow precision alignment of racing kart chassis for less rolling friction and higher top speeds as well as improved acceleration and handling.
|
|
Wheel Alignment Discs, Metric Pattern (Pair) (SKU: FK2075)Steel Wheel Alignment Discs allow precision alignment of racing kart chassis for less rolling friction and higher top speeds as well as improved acceleration and handling. The Discs bolt onto the hub in place of the tire and rim assembly allowing you to set toe in and camber with the driver sitting in the kart. This is very important as the front end requires adjustments with the kart fully loaded and the chassis in compression.
|
|
|
|
