 "Steering Shaft Support 19mm Type II" (SKU: FK1019)"Type ll has two mounting holes...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
"Steering Shaft Support, 20mm, Type II" (SKU: FK2019)"Type ll has two mounting holes...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 "Steering Shaft Support, 19mm, Type I" (SKU: FK1018)"Type l has one mounting hole...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 "Steering Shaft Support, 5/8"" , Type III" (SKU: FK1011)"Type lll has three mounting holes, one above & two below the shaft brg...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 "Steering Shaft Support, 5/8"", Type IV" (SKU: FK1012)"Type lV has three mounting holes below the shaft brg...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort."
|
 Clamp Brackets With Extension for 1 1/4" Tube (SKU: FK3035)"Our Clamp brackets have superior clamping power. Perfect for mounting exhaust systems, weights, number panels, and body work.. The special design allows the brackets to firmly grip even severly undersized tubing. Each assembly is machined as a set to guarantee a perfect fit. Made from ¾ inch square 6061-T6 aluminum . Complete with hardware."
|
Clamp Brackets With Extension for 1 1/8" Tube (SKU: FK3030)"Our Clamp brackets have superior clamping power. Perfect for mounting exhaust systems, weights, number panels, and body work.. The special design allows the brackets to firmly grip even severly undersized tubing. Each assembly is machined as a set to guarantee a perfect fit. Made from ¾ inch square 6061-T6 aluminum . Complete with hardware."
|
Clamp Brackets With Extension for 1" Tube (SKU: FK3010)"Our Clamp brackets have superior clamping power. Perfect for mounting exhaust systems, weights, number panels, and body work.. The special design allows the brackets to firmly grip even severly undersized tubing. Each assembly is machined as a set to guarantee a perfect fit. Made from ¾ inch square 6061-T6 aluminum . Complete with hardware."
|
|
Clamp Brackets With Extension for 3/4" Tube (SKU: FK3015)"Our Clamp brackets have superior clamping power. Perfect for mounting exhaust systems, weights, number panels, and body work.. The special design allows the brackets to firmly grip even severly undersized tubing. Each assembly is machined as a set to guarantee a perfect fit. Made from ¾ inch square 6061-T6 aluminum . Complete with hardware."
|
 Control Rods (Tie rods). 5/16 NF x 7 Inches (SKU: FK9700)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
Control Rods (Tie rods). 5/16 NF x 9 1/2 Inches (SKU: FK9950)Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification.
|
 Pedal Grips Pair, EURO! ~ (2 pieces) (SKU: FK825)"Secure, slip free control is yours when you slip these knurled aluminum grips over your Tubular gas and brake pedals. FK825 is available in Red, Silver, Blue and Black. Superior quality and workmanship that can only be found at FAST KARTS . "
|
 Publication - "Dynamics of Speed" (SKU: DOS 0001)"Dynamics of Speed" is a reference book specifically for karting, a worthy addition to your library.
|
 Rod Ends, 3/8" Male Threrad ~ LH and RH (SKU: CH008)For your steering system or any other use. These fit our 3/8" threaded Control Rods (Tie Rods).
Please note LH or RH on the order form and the quantity you need of each.
|
Rod Ends, 5/16" Male Thread ~ LH and RH (SKU: CH007)These are for karts using the smaller 5/16" rod ends. Note on the order form LH or RH thread and the quantity of each needed.
Generally each tie rod uses 1 of each. These fit our 5/16" Control Rods (Tie Rods).
|
 Sprockets, #35 ~ 53T to 63T (SKU: DR001)Brand name sprockets, how many teeth do you need?
Note number of teeth wanted on order form...
|
|
Sprockets, #35 ~ 64T - 78T (SKU: DR002)Brand Name Sprockets, larger sizes.. Note number of teeth wanted on the order form.
|
 Steering Lock for 5/8" Shaft (SKU: FK850)"This is the Lock & Pin only for a 5/8"" steering shaft. See FK835 for lock w/steering block."
|
 Steering lock & Steering block Set 20mm shaft ~ (New) (SKU: FK8020)Steering lock with matching steering shaft block (FK2019) to aid in setting steering geometry. Use with 20mm shaft.
|
Steering lock only 19mm shaft (SKU: FK819)Steering lock . Use with 19mm shaft...
|
|
Steering Lock only: 20mm shaft (New) (SKU: FK820)Locks the steering for wheel alignment & toe-in adjustments.
|
Steering Support w/Lock, 19mm (SKU: FK8019)"Included is a Type II Steering Block, Steering lock & Pin for a 19mm steering shaft."
|
Steering Support w/Lock, 5/8" Shaft (SKU: FK835)Included is a Type II Steering Block, Steering lock & Pin for a 5/8"" steering shaft.
|
|
