| • |
"Steering Shaft Support 19mm Type II" "Type ll has two mounting holes...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
"Steering Shaft Support, 20mm, Type II""Type ll has two mounting holes...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
"Steering Shaft Support, 19mm, Type I" "Type l has one mounting hole...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
"Steering Shaft Support, 20mm, Type I""Type l has one mounting hole...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
"Steering Shaft Support, 5/8"" , Type III" "Type lll has three mounting holes, one above & two below the shaft brg...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
"Steering Shaft Support, 5/8"", Type II""Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
"Steering Shaft Support, 5/8"", Type IV" "Type lV has three mounting holes below the shaft brg...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
"Steering Shaft Support, 5/8"", Type I""Type l has one mounting hole...Each block is fully machined from 6061-T6 Aluminum, polished & anodized Red. These have needle bearings, offering precise steering control with minimal effort." |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 10 3/4 Inches Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 10 InchesFast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 11 1/2 InchesFast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 11 InchesFast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 12 1/2 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 12 3/8 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 13 1/4 InchesFast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 13 5/8 InchesFast Kart control rods are machined from 1/2 inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 6 1/2 Inches Fast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 7 3/4 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 7 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 8 1/2 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 8 1/4 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 8 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 9 1/2 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 9 1/4 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 9 3/4 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 9 5/8 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 3/8 NF x 9 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 5/16 NF x 10 1/2 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 5/16 NF x 10 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
| • |
Control Rods (Tie rods). 5/16 NF x 11 1/2 InchesFast Kart control rods are machined from ½ inch hex aluminum. The left hand threaded end has a machined groove on the O.D. to allow easy identification. |
|
|
